Multi-Plex Units

“We provide a wide range of services from the fabrication of hard to locate parts to complete customization along with general maintenance and servicing.”

Overview

Many applications require more than a standard pump to deal with unique pumping problems. For these situations, complete engineering support can prove invaluable. Our staff of experts can create a specific pumping unit that can maximize output and safety and minimize cost.

Features

  • Features of the Energyfab Multi-Plex Unit
  • Triplex Pump H.P. up to 600
  • Up to 15,000 PSI Discharge Pressure
  • 16m Btu/hr Heat Exchanger
  • Duel Hydraulic Systems
  • D.O.T. 412 Storage Tank w/ *******
  • Up to 1000 gal. Propane Storage

Typical Multi-Plex Unit Specifications

 

Typical Energy Fabrication Multi-Plexl Unit Specifications Sheet
16mBtu/HR HEAT EXCHANGER 50'-1 V2" H.P. HOSE
STD. PROPANE FIRED w/TEMP CONTROLLER 3 x 2 - 13 CENTRIFUGAL PUMP - HYD. DRIVE
STEEL VAPORIZER w/1" HOSES 3" BOWIE PUMP - HYD. DRIVE
2" STD. COIL ASSY - DOMESTIC MATERIAL w/ISOLATION VALVES 30 GPM HYD. COOLER w/FAN - AUTOMATIC CONTROL
ANSUL REMOTE ACTUATED 30 LB FIRE EXTINGUISHER ALUMINUM CONTROL PANEL - WEATHERPROOF & HEATED w/COVER
CERAMIC FIBER INSULATION w/SST MESH
 DUAL PRESSURE GAUGES - HI & LO
DUAL BURNER BOX TOOL BOXES - 6' EACH SIDE PROPANE PRESSURE GAUGE
ACCESS LADDER ELECTRONIC RPM/LCD & RATE METER- LCD
20" MANWAYS MURPHY HI-TEMP SHUTDOWN (SMALL ONE)
2" CLEAN OUTS IN EACH COMPARTMENT 2000 SERIES COMPUTER & LAPTOP
75 BBL TANK - ROUND SHELL DESIGN - DOT 412 SPLIT TANK 50-FRONT 25-REAR RATE, TOTAL, PRESSURE TO 15K, TEMP TO 500°F
VENTLINES OVER THE TOP OF PROPANE TANKS
 TRIP HI-PRESSURE TO ACTUATE CLUTCH w/AIR SOLENOID
FLOAT GAUGES TRIP HI-TEMP TO ACTUATE BALL VALVE FAIL CLOSE ON PROPANE
MSI 600 HP TRIPLEX w/3.5" PLUNGERS 10,399 MAX PSI DUAL VAPORIZERS
8 BPM MAX VOLUME Oa 3000 PSI STEEL PROPANE LINES
784 SPICER TRANSFER CASE COVER FOR CONTROL PANEL - PLEXIGLASS
2" SCH 160 H.P. PIPING w/2" CHECK VALVE 10,000 PSI TEST 6,000 PSI WORKING CONTROL PANEL TO FACE REAR
2" SCH 160 TO REAR ENGINE WATER & OIL GAUGES
2" SCH 80 LOW PRESSURE PLUMBING
 AIR SWITCHES TO CONTROL PUMPS PTO'S & VALVES
5 - 2" JAMESBURY BALL VALVES ON LOW PRESSURE- ISOLATE COILS HAND CLUTCH
3" SCH 40 SUCTION PLUMBING w/BUTTERFLY VALVES THROTTLE SWITCH
4" SCH 40 CENTRIFUGAL PLUMBING FOR SUCTION WORK LIGHTS & ELECTRONIC SWITCHES FOR POWER, ETC.
ALL GAUGES & VALVES ON LOW PRESSURE PILOT & BURNER CONTROLS
GAUGES ON H.P. FOR COLD WEATHER OPERATION 480 GALLONS PROPANE w/1 SINGLE TANK BEHIND
FULL LENGTH SKIRTING w/TOOL BOXES
 HAND HELD FIRE EXTINGUISHER
4 - LOCKING TOOL BOXES EXTERIOR SANDBLASTED, PRIMED, & PAINTED TO YOUR SPECS w/IMRON 44451 DK CARMEL MET.
DUAL PIPE RACK FOR 6 JOINTS PASS SIDE STEEL- 4 JOINTS DRIVERS SIDE - 2 ALUMINUM, 2 STEEL 50'- 3" SUCTION HOSE
DUAL HOSE RACK w/2" - I OK LONG SWEEPS
Typical Rigging Specifications
TEE Gardner Denver Triplex- 4 x 5 3500 PSI 5 BPM Outside Clutch & Bowie Control
3" x 4" Centrifugal Charge Pump - Mech. Drive Rate Meter & Totalizer
3" Bowie Load Pump - Mech. Drive Brass Quick Connects
H.D. Kompensator 5th Wheel, Fenders & Mud Flaps Plunger Lube System
Plumbed w/4" Plumbing & Viton Butterfly Valves - Rigged to Load, Unload & Charge w/Either Pump Drip Catch for Triplex
Oilbath Chain Drive on Triplex 1 - Chiksan Joint to Ground Level
784 Spicer Transfer Case Painted to Your Specs
Inside Cab Controls